VolcanoBox 1.9.9
Truly World's 1st
▬● Truly World's 1st ALL MTK ANDROID ROOT (beta)
▬● Truly World's 1st MTK ANDROID CUSTOM AREA WRITE FLASH
▬● Truly World's 1st MTK ANDROID CUSTOM AREA READ FLASH
▬● Truly World's 1st SPD ANDROID IMEI REPAIR
▬● MTK6253 decryption
How to Root Any MTK Android phone ?
1- Set pinouts or detect pinouts
2- Go to mtk tab
3- Select Boot Built-in-Boot-12
4- Click on read info
5- Untick auto pinfind
6- Make sure your phone com port selected
7- Click on run
8- Read carefully BOOTIMG address
9- Click on Read Flash
10- Write BOOTIMG ADDR into Start Address ( without 0x )
11- Write BOOTIMG length into Flash Size ( without 0x )
12- Click on reset pinouts
13- Click on run
14- Save file
15- Go to Tools
16- Click on One-key Root
17- Click on Select Open
18- Select your read file of BOOTIMG
19- Click on Convert
20- Go to MTK tab
21- Click on write flash
22- Select Built-in-Boot-12
23- Select Converted File
24- Write BootIMG ADDR into START ADDRESS
25- Click on Reset pinouts
26- Click on write
27- After writing Your phone will be ROOTED !!!!!
How to Read and Write Custom/Specific Area File to MTK Android ?
1- Set pinouts or detect pinouts
2- Go to mtk tab
3- Select Boot Built-in-Boot-12
4- Click on read info
5- Untick auto pinfind
6- Make sure your phone com port selected
7- Click on run
8- Read carefully BOOTIMG address ( or your desire area address )
9- Click on Read Flash
10- Write BOOTIMG ( or your desire area address ) ADDR into Start Address ( without 0x )
11- Write BOOTIMG ( or your desire area length ) length into Flash Size ( without 0x )
12- Click on reset pinouts
13- Click on run
14- Save file ( your desire area file read done )
Now how you can write ?
1- Set pinouts or detect pinouts
2- Go to mtk tab
3- Select Boot Built-in-Boot-12
4- Click on write flash
5- Select Your desire File
6- Write BootIMG ( or your desire area address ) ADDR into START ADDRESS
7- Click on Reset pinouts
8- Click on write
9- Your desire File write done !!
How to Write SPD Android imei ?
1- goto detect tab
2-select spd from list
3-attach phone
4-click on detect tab
5- press detect (keep in mind where is D- and D+ gnd)
6- clear pinout
7-close volcano
8- again open volcano
9- mobile connect with volcano jig but volcano phone cable remove to volcano
10- go to detect tab select spd
11- select d-, d+ and gnd manual and set pinout(where it's detect before)
12- go to spd tab
13- R/W IMEI chooses com
14- untick auto detect pinout
15- press these key from keybord to enable imei alt+ctrl+i
16- select boot 6530
17-click on write imei
18-click run
19-new window will be open
20 -choose usb
21-write imei in box
22-click on write imei
23-then connect volcano jig cable jack in volcano
IF WRITE IMEI WITH USB CABLE DISSCONNECT USB + SUPPLY VCC WORK WITH ONLY THREE WiRE D+ D- GND
if write imei usb with usb cable and boot key mobile, dissconect usb + supply (vcc)
usb cable connect only D+ D- GND
1-go to spd tab
2-R/W IMEI chooses com
3-untick auto detect pinout
4-press these key from keybord to enable imei alt+ctrl+i
5-click on write imei
6-click run
7-new window will be open
8-choose usb NOT SELECT ANY COM PORT
9-write imei in box
10-click on write imei
11-then connect press mobile boot key and inseri usb(connect only three wire usb D+ D- GND VCC +SUPPLY NOT CONNECT) AFTER 10 15 SEC YOUR ANY SPD IMEI WRITE
